The Weak Signal Propagation Reporter Network is a group of amateur radio operators using K1JT's MEPT_JT digital mode to probe radio frequency propagation conditions using very low power (QRP/QRPp) transmissions. The software is open source, and the data collected are available to the public through this site.

Now to figure which software to download and install so I can use this/these mode/s with my Yaesu FTdx-3000. I do have and sometimes use Ham Radio Deluxe. I have downloaded WSJT-x. It appears to be "hearing" stuff as evident in the waterfall display. So far however, no decode is evident. Maybe someone can direct me to the next steps and/or point my browser to a step-by-step instruction set.
Thank you

Replaced the reception endfed antenna for a mini whip antenna at 5m height. The SDR waterfall display seems much cleaner now and signal to noise level is improved.

1st try was OCF at 55'. Next is Fan dipole at 40'.

Introduction: The Kenwood TS-590 and the Icom IC-7600 have a USB port which can be used transfer the audio signals to and from the radio. Other transceivers without a similar USB connection may need an external data interface device with built-in USB Sound Card such as the ZLP Electronics Data-Link, MiniProSC or Pro3 data interface from G4ZLP or the Tigertronics SignaLink USB for example. I have previously used a Tigertronics SignaLink USB with my Icom IC-706mk2g. I now use the excellent G4ZLP Data-Link with my Yaesu FT-891 (see my separate post for those settings)

Icom IC-706mk2g with Tigertronics SignaLink USB

Drivers: Firstly I installed the SignaLink USB as per the Tigertronics instruction manual. Installation depends upon the Operating System being used but everything is described in detail in the manual, on the Tigertronics website and downloadable manuals.

The laptop (Windows XP) shows the SignaLink as USB Audio Codec which can be accessed via the sound card settings and progams that require them, such as WSPR.

Kenwood TS-590 Set Up

Drivers: Firstly I installed the Kenwood virtual COM port drivers (Silicon Labs C_210x USB to URT Bridge) and the ARCP590 radio control program onto the old XP laptop - not strictly necessary for WSPR, but I thought it would be useful for other occasions.

In case it's helpful to anyone, here are the settings that I find work with my Yaesu FT-891 and a G4ZLP / ZLP Electronics Data-Link USB Sound Card. I would think that this will be much the same for other USB sound cards, such as the ZLP Mini-ProSC, ZLP Pro3 and SignaLink USB.

The main puzzle that I had was finding the correct RX and TX BFO settings. This is 1500Hz. Data Mode is OTHERS Data PTT will be DAKY and as the sound card is connected to the rear of the radio, Data In Select is REAR. Data BFO is USB (upper side band). Power as low as possible - 5 watts.

Space Weather Message Code: ALTK07
Serial Number: 113
Issue Time: 2018 Aug 26 0739 UTC

ALERT: Geomagnetic K-index of 7
Threshold Reached: 2018 Aug 26 0738 UTC
Synoptic Period: 0600-0900 UTC

Active Warning: Yes
NOAA Scale: G3 - Strong

2018-08-23 01:36 D13PZE 0.475755 -23 0 JF62 +40 10.000 N2LO FN20rg 12404 7707

Actually, it was +40dBm which is 10 Watts!

D13PZE 0.475755 -23 0 JF62

anyone have info on D13PZE?

Read my blog entry "Swedish icebreaker Oden and the mystery of SA2LLL/63" on

I'm making the new site which summarize WSPR reports within past 24 hours.
You need to enter WSPR RX or TX callsign to show you the report.
If any request or comment, please ask me.


Last week I finally got around to upgrading my ham radio license from technician to general. I passed the technician exam 18 years ago when I was in middle school so passing my general exam was a goal of mine for a long time. Now that my upgrade is posted on the FCC website I thought I would celebrate so I got my Raspberry Pi setup and transmitting on 20 meters. So far with my silly wire antenna set up on my front porch, I've been heard by a guy across town and two people in Texas. That gives me a range of 14 miles or 1400 miles.